How to Adjust Draw Length on a Bear Compound Bow

Video bear species draw length adjustment

Most modern bows have a complex method to adjust the draw length, and most require a bow press.

However, Bear compound bows are generally very easy to adjust and do not require the use of a bow press.

For this reason, Bear compound bows are one of the best bows for beginners.

Bear Adjustment System

How to Adjust Draw Length on a Bear Compound Bow

Bear bows are one of the most beginner-friendly compound bows on the market.

This is because Bear archery made their bows completely adjustable for the draw weight and even the draw length.

There are some variations between the models, but the concept is generally the same.

Adjusting the Draw Length

Adjusting the draw length on your Bear compound bow is quite simple and can be done in less than ten minutes.

There are two steps to adjusting the draw length of a compound bow. First, we will adjust the module; this will set the draw length to your desired length.

Second, we must set the stop; this will ensure that the cams stop turning when you drawback.

Tools Needed

How to Adjust Draw Length on a Bear Compound Bow

Adjusting a Bear compound bow is so easy that there are no tools needed other than the right size Allen keys.

This varies from model to model, so I like to have an Allen key set.

Fitting the small screws can also be a bit tricky, so I like to put my bow in a bow vice when adjusting it; however, this isn’t necessary.

Adjusting the Module

How to Adjust Draw Length on a Bear Compound Bow

A compound bow module determines the draw length of a compound bow.

Many modules have only a limited range, allowing the bow to be adjusted in only small increments or in some cases, not at all.

See also  How High Should My Tree Stands Be?

However, the modules found on a Bear compound bow have a wide range of adjustments and, in most cases, do not need to be swapped for any size draw length.

How to Adjust Draw Length on a Bear Compound Bow

To adjust the draw length on the bear compound bow module:

  1. Find your draw length number. Once you know your draw length, you can find it’s corresponding number on the bear compound bow cam. For example: on a Bear Wild compound bow a 28 inch draw is number 4 on the module.
  2. Secure the bow in a position that is comfortable to work on.
  3. Locate the module. This is usually located on the cam on a single cam bow. On a dual cam bow the module is typically located on the tom cam.
  4. Unscrew the two screws on the back of the module. Be careful not to lose the screws as the module will fall once the two screws are undone.
  5. Slide the module to the number that corresponds with your draw length.
  6. Locate the two holes that perfectly align between the module and the bow and redo the screws. Hand tighten the screws and be careful not to overtighten.

Adjusting the Stopper

How to Adjust Draw Length on a Bear Compound Bow

Now that the draw length is set, we have to set the stopper to align with the draw length.

  1. Locate the stopper. Typically on a single cam bow, the stopper is located on on the outside of the cam.
  2. On a dual cam bow, there are two stoppers, and it is important that both are set equally to ensure your bow is firing evenly.
  3. Undo the stopper and set it to the same number as what you set the module to.
  4. Drawback your bow to check your draw length.
See also  The Math in the Meat

Important Things to Remember

Ensure that you are using the proper tools. Some bow manufacturers use metric measurements, and others use imperial. Find the one that fits your bow perfectly to prevent damaging the screws.

Double-check that you are undoing the proper screws. There are a lot of screws around the cams of a bow, so it’s important to double and triple-check that you have the correct screw.

Undoing the wrong screw could cause damage to the bow and injury to you.

Final Thoughts

Adjusting the draw length on a Bear compound bow is straightforward.

Once you find your corresponding number on the module to match your draw length, it’s only a matter of moving the module and the stopper to that number.

The whole process takes less than ten minutes, and you’re back up shooting again.

It’s easy to mistake the screws, so double-check that you have the right screw before undoing it to prevent damage and possible injury.

Previous articleDeer Hunting Debate: Does Culling Really Work?
Next article10 interesting facts about lion eyes
Ethan Smith is a seasoned marine veteran, professional blogger, witty and edgy writer, and an avid hunter. He spent a great deal of his childhood years around the Apache-Sitgreaves National Forest in Arizona. Watching active hunters practise their craft initiated him into the world of hunting and rubrics of outdoor life. He also honed his writing skills by sharing his outdoor experiences with fellow schoolmates through their high school’s magazine. Further along the way, the US Marine Corps got wind of his excellent combination of skills and sought to put them into good use by employing him as a combat correspondent. He now shares his income from this prestigious job with his wife and one kid. Read more >>