Elevated Deer Blind Plans

0
126
Video elevated deer stand plans

2.8K

This step by step diy woodworking project is about elevated deer blind plans. The project features instructions for building an elevated 6×6 deer blind. This project features opening on all sides and a roof with 15 degree slope. Make sure you take a look over the rest of plans to see alternatives and more projects for your garden.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day.

Projects made from these plans

Elevated Deer Blind Plans

Cut & Shopping Lists

  • A – 8 pieces of 4×4 lumber – 77 1/2″ long POSTS
  • B – 4 pieces of 2×6 lumber – 72″ long, 8 pieces – 69″ long JOISTS
  • C – 1 piece of 3/4″ plywood – 48″x72″ long, 1 piece – 24″x72″ long FLOOR
  • D – 2 pieces of 2×4 lumber – 65″ long, 2 pieces – 72″ long, 2 pieces – 62″ long, 4 pieces – 22 1/2″ long, 4 pieces – 32 1/2″ long BACK WALL
  • E – 2 pieces of 2×4 lumber – 65″ long, 2 pieces – 72″ long, 2 pieces – 62″ long, 4 pieces – 22 1/2″ long, 4 pieces – 32 1/2″ long FRONT WALL
  • F – 6 pieces of 2×4 lumber – 72″ long, 2 pieces – 65″ long, 4 pieces – 22 1/2″ long, 4 pieces – 32 1/2″ long 2xSIDE WALL
  • G – 2 pieces of 3/4″ plywood – 24″x83 3/4″ long, 2 pieces – 48″x83 3/4″ long, 2 pieces – 24″x90 3/4″ long, 2 pieces – 48″x93 3/4″ long WALLS
  • H – 2 pieces of 2×4 lumber – 9″ long, 1 piece – 72″ long TOP RIDGE
  • I – 12 pieces of 2×4 lumber – 35 3/4″ long RAFTERS
  • 8 pieces of 4×4 lumber – 8′
  • 12 pieces of 2×6 lumber – 6′
  • 51 pieces of 2×4 lumber – 6′
  • 2 pieces of 2×3 lumber – 6′
  • 8 pieces of 3/4″ plywood – 4’x8′
  • 1 1/4″ screws
  • 1 5/8″ screws
  • 2 1/2″ screws
  • filler, stain
  • glue
See also  When to Plant Beans and Peas for Whitetail Deer

Tools

Hammer, Tape measure, Framing square, Level

Miter saw, Drill machinery, Screwdriver, Sander

Safety Gloves, Safety Glasses

Time

One week

Make sure you follow us on Facebook to be the first that gets our latest plans and for some other exclusive content. Also, follow us on Pinterest to get many ideas for your backyard from all the internet! Check out our YouTube channel! See how you can Support Us with no extra costs to you.

How to build an elevated deer blind

The first step of the project is to build the frame for the deer blind. Cut the components from 2×6 lumber. Drill pilot holes through the rim joists and insert 2 1/2″ screws into the regular joists. Place the joists equally-spaced and make sure the corners are square.

Next, you need to fit 4×4 posts into the ground. You can adjust the size of the elevation to suit your needs. Use batter boards and string to align the posts. Measure the diagonals and apply the 3-4-5 rule to the corners.

You have to set the posts 3′ into the ground. Plumb the posts with a spirit level. Use temporary braces to lock the posts into place while the concrete dries out. Use a spirit level to make sure the top of the posts are horizontal.

Fit the frame to the top of the posts and lock it into place with 3 1/2″ screws. Make sure the frame is horizontal and drill pilot holes to prevent the wood from splitting. Fit another frame to the bottom of the posts, in order to enhance the rigidity of the structure.

See also  Catch this land-walking fish in California? Don’t toss it back; do this instead

Use 3/4″ plywood sheets for the floor of the deer blind. Align the edges with attention and leave no gaps between the components. Use 1 5/8″ screws to lock the sheets to the joists, every 8″.

Build the side walls from 2×4 lumber. Cut the components at the right dimensions. Drill pilot holes through the plates and insert 2 1/2″ screws into the studs.

Fit the side walls to the floor of the deer blind. Align the edges with attention, plumb the walls with a spirit level, drill pilot holes and insert 3 1/2″ screws into the floor.

Build the back wall from 2×4 lumber. As you can see in the diagram, you need to frame the door opening in the left side.

Build the front wall of the elevated deer stand. Assemble everything with attention. Make sure the corners are square and leave no gaps between the components.

Fit the front and back walls to the floor. Drill pilot holes through the bottom plates and insert 3 1/2″ screws into the floor. Make sure the corners are square and align the edges before locking the walls together. Secure the adjacent studs together. Drill pilot holes and insert 2 1/2″ screws.

Next, you need to install the top ridge to the top plates. Build the components from 2×4 lumber. Drill pilot holes and insert 2 1/2″ screws to lock the components together. Use a spirit level to make sure the supports are plumb and check if the top ridge is horizontal.

Build the rafters from 2×4 lumber. Cut both ends of the rafters at 75 degrees.

Fit the end rafters to the top plates, as shown in the diagram. Build the components from 2×3 lumber. Fit the components to the top plates, drill pilot holes and secure them into place using 3 1/2″ screws.

See also  A Beginner’s Guide to Crossbow Hunting

Fit the rafters to the rafters to the top of the deer box. Place the rafters equally-spaced. Drill pilot holes and secure the rafters to the top ridge and to the top plates using 3 1/2″ screws.

Build the panels for the front wall from 3/4″ plywood. Use a saw to make the notches to the sheets and smooth the cut edges.

Fit the panels to the back wall and align the edges with attention. Use 1 5/8″ screws or nails to secure the sheets to the framing, every 8″.

Build the panels for the front wall from 3/4″ plywood. Insert 1 5/8″ screws or nails to secure the panels to the studs, every 8″.

Build the side walls from 3/4″ plywood. Take accurate measurements and make the cuts with a circular saw. Align the edges and secure them to the framing using 1 5/8″ screws or nails.

This deer blind has a basic design and can be built by any person with common woodworking skills. You can adjust the dimensions of the deer box, while using the same techniques described in the plans

Top Tip: Make sure you check out the part 2 of this project, to learn more about how to build the roof and the door for the elevated deer box. If you want to get PREMIUM PLANS for this project, in a PDF format, please press GET PDF PLANS button bellow. Thank you for the support.

This woodworking project was about free elevated deer blind plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

EXPLORE MORE IDEAS FOR:

Previous articleDWR shuts down antler gathering to protect Utah’s big game
Next articleThe 4 Best Turkey Mouth Call [Hands-On]
Ethan Smith is a seasoned marine veteran, professional blogger, witty and edgy writer, and an avid hunter. He spent a great deal of his childhood years around the Apache-Sitgreaves National Forest in Arizona. Watching active hunters practise their craft initiated him into the world of hunting and rubrics of outdoor life. He also honed his writing skills by sharing his outdoor experiences with fellow schoolmates through their high school’s magazine. Further along the way, the US Marine Corps got wind of his excellent combination of skills and sought to put them into good use by employing him as a combat correspondent. He now shares his income from this prestigious job with his wife and one kid. Read more >>